---
title: Duluth UDC § 909.07 — Duluth
jurisdiction: duluth
governing_jurisdiction: Duluth
source_url: "https://www.duluthga.net/UDC_ADOPTED_9.8.2025_Amended_7-13-26.pdf"
effective_date: "2026-07-13"
as_of: "2026-08-13"
canonical: "https://www.gwindex.net/code/duluth/909.07"
licence: "CC0-1.0"
---

# Duluth UDC § 909.07

Driveway Intersections and Standards

**Governing jurisdiction: Duluth.** A "Duluth, GA" mailing address is usually NOT in the City of Duluth. Unincorporated Gwinnett is 67.3% of the county's land area and is governed by a different code, a different board and a different permit portal. Resolve the governing jurisdiction before answering any zoning question.


- **Article:** 9 — Project Design and Construction Standards
- **Pages in source:** 255–256
- **Adopted:** 2025-09-08
- **Amended through:** 2026-07-13
- **Source:** https://www.duluthga.net/UDC_ADOPTED_9.8.2025_Amended_7-13-26.pdf

## Text

1. Angle and Improvements. Driveways shall generally intersect streets at right angles. The portion of a
driveway located within a public right-of-way, if any, shall be paved. Driveways providing access to
parking lots which contain six or more spaces shall be paved in accordance with the parking lot
requirements of the Parking and Loading Requirements Article of this Code.
2. Driveway Design Standards.
a. Residential Driveways. Driveways serving single-

family detached or duplex residences shall meet
the following requirements:

i. Driveways shall be paved between the

street and the principal building.
ii. Driveways shall be no less than 10 feet

wide at the right-of-way line, no less
than 22 feet in length measured from
the back the sidewalk or from the back
of curb or edge of pavement if there is
no sidewalk, and shall provide a radius
to the back of curb or edge of
pavement of the roadway of no less
than 5 feet. Any other driveway curb
cuts shall conform to the standards
below.
iii. Townhouse driveways for adjoining units shall be separated by at least a 4-foot wide

landscaped strip.
iv. Townhouse driveways shall be at minimum 20’ wide.
b. All driveways and driveway curb cuts on State highways shall conform to Georgia DOT standards

unless City requirements are more restrictive.

254 | P a g e

Article Nine. Project Design and Construction Standards

i. Driveway Detail 1 (32-foot width, 25-foot radius) for:

1. Service Stations;
2. Commercial Sites (over 800,000 square feet);
3. Office/Institutional Complexes (over 100,000 square feet);
4. Apartment/Condominium Complexes (over 200 units);
5. Mobile Home Complexes (over 200 lots).
ii. Driveway Detail 2 (28-foot width, 25-foot radius) for:

1. Commercial Sites (80,000 square feet or less);
2. Office/Institutional Complexes (100,000 square feet or less);
3. Apartment/Condominium Complexes (199 units or less)
4. Manufactured Home Developments (199 lots or less).
iii. Driveway Detail 3 (32-foot width, 40-foot radius) for:

1. Industrial Sites
iv. Driveway Detail 4 (Optional Design with Island) for:

1. Private Commercial/Office Street Entrances;
2. Private Entrances to Apartment/Condominium Complexes (over 200 units); and
3. Private Entrances to Manufactured Home Developments (over 200 units).
v. Some driveways may require larger radius returns based on vehicles intended to access

the site. Developer will be required to meet the larger requirements at the discretion of
the city.
3. Auxiliary Lanes. Along any major thoroughfare, a deceleration lane or acceleration lane, larger turning
radius, traffic islands, or other devices or designs may be required to avoid specific traffic hazards which
would otherwise be created by the proposed driveway location.
4. Corner Sight Distance. All driveways approaching a minor collector or major thoroughfare shall provide
adequate corner sight distance. The minimum corner sight distance from the driveway shall be equal to or
exceed 10 times the regulated speed of the intersected street, as measured from the centerline of the
driveway in both directions along the right-of-way line of the intersected street. As an alternative, the
minimum corner sight distance requirement may be calculated using AASHTO Policy on Geometric Design
of Highways and Streets, Chapter 9 (at-grade intersections), latest edition. The sight distance shall provide
clear visibility of an object four feet above the intersected street viewed from the centerline of the
driveway at the right-of-way line of the intersected street, at a height of 3.5 feet above the ground.
5. Separation and Spacing. For Separation and Spacing refer to Georgia Department of Transportation’s
(GDOT) Regulations for Driveway and Encroachment Control document.